Well, I should have the back deck, phase two, completed by now, but no. Actually, "phase two" is just another choice of saying "all the work I didnt finish last summer like I planned." Hmm.
If things had gone like they should have, Id have cracked on like smoke and oakum and we would now be enjoying the midnight sun on the back deck. But sunny day after sunny day slipped by as I did this and that. When I did try to work on the deck, I first had to figure out what the heck I was thinking when I last stopped. That took most of one day. Then, I had to undo some mistakes I made after misinterpreting what I had been thinking when I last stopped. That took another day. Then I realized that I never ordered enough decking. So I ordered it. It came. So did the rain.
So, I worked in the shop instead. Yea!
While rethinking the deck, I found I had an unneeded pressure treated 4x4. I decided that it should replace the street address post at the end of our drivechoice - which truth be told was a 1x3, sharpened to a point, driven into the ground with our address scrawled on it with a Sharpie (or possible a Sir Marks-A-Lot). This new post would have spiffy reflective numbers and a decorative cap. The numbers came from the Borg, but the decorative cap was going to come from my shop.
I wanted this to be a quick project, so I worked rather fast and loose, which was actually fun. First I needed to create a horizontal element. For this I wanted a square that would overhang all the sides of the post evenly. Instead of measuring, I used the sliding extension on my folding rule to capture the difference between the width of the stock and the width of the post...
...and then directly transferred that to the face of the stock (marked a line, set the post section to the line and added the extension distance) to determine the correct length to cut. Could I have measured? Sure, but it would have been slower and no more accurate.
I should point out that I wasnt concerned by the rough edge of the board I was using as I planned to round it over. In the end I didnt like how it came out, but if you look closely you can spot it in the background in a later picture.
As the stock I was using was an off-cut from the deck, it had kerfing on one side. This wouldnt do. Time for the scrub plane!
The scrub, followed by the jack, and the stock was ready to go. I used to clamp everything I planed between a bench dog and the vise dog in my end vise. Over time, Ive switched to doing most of my planing with the stock just butted against a bench dog, as shown here. Even with side-to-side adjusting (not needed as often as you might think) its much faster.
Next, I wanted to make a pyramid to top the cap. Some quick layout, and sawing, followed by the trusty jack and there it was:
It was at about this point (no pun intended) that I scrapped the rounded over look for the horizontal square. I decided to make another, and wrap it in mitered moulding. So I dug out the sticking board, selected a profile and got to work.
My sticking board has a built in miter box in the fence, which is handy, if not too accurate. 
Lurking in the background is the stair nosing plane I used to round over the edges of the first square.
Since my miters were not great, I needed to adjust them with a chisel. The sticking board made a handy fixture for this.
It is also great for holding the work while drilling, such as for these pilot holes for the nails in the moulding. The fence holds the stock securely with no need for clamping. I do this often, as you can tell by the number of holes in the sticking board.
In the left background is the first square I made, in the right background is the second one, with the first piece of moulding already in place.
I added two more layers of moulding - a thumbnail above the square, and a dropped ogee below it. They came out a little rough, a combination of fast and loose working and not so great stock selection (I ripped some sticks from another decking off-cut). Heres the final cap with all elements in place:
And here it is in place on the actual post at the end of the drivechoice:
The tool kit used on this project (missing the sticking board).
One of the things I liked about this project was the reminder about the place of perfection. There is a lot more going on in a piece than just perfection of each part. Imperfect parts can be put together into a pleasant whole; perfect parts can be assembled into a ghastly whole. I think the whole (including proportion, character, sense of place etc.) has the overriding influence. Of course, perfect parts can help create a better whole...
P.S. - If you are sharp eyed, and a bit of a photo details nerd (like me), you may have spotted the elusive candle rack on the bench in several photographs. Yep, Im still working on it...
0 komentar:
Posting Komentar